Measurement System Accessories

Tilt and Center Worktables

 

 

Tilt_center-1024x768
Low-Profile-Granite-Base_End-3

Custom Frame Heights (Low Profile Shown)

 

Vacuum Controllers

These units run off of shop air and have built-in vacuum release buttons, selectable adjustable high and low vacuum options, and gages to display incoming air pressure and the current vacuum.

vacuum-control-3
custom-fixture-3-2

Small Custom Jigs

This small custom jig is ideal for small rotary tables up to 200mm in diameter, but can also be used for larger tables up to 400 mm in diameter. The fixture plates are accurately located and fastened directly on the rotary table. This simple, economical method allows using modular fixturing or dedicated permanent fixturing. ABTech has custom vacuum jigs available as well.

Large Custom Jigs

This large custom jig is ideal for medium rotary tables up to 400mm in diameter. The fixture plates are accurately located and fastened directly on the rotary table. This simple, economical method allows using modular fixturing or dedicated permanent fixturing. Custom vacuum jigs are available as well.

custom-vacuum-fixture
Collet-Chucks-2-1

Collet Chucks

These collet chucks are commonly used with multiple parts of the same size or smaller diameters that have limited ways to remain secure during a measurement.

Scroll Chuck with 3-Point contact

• High-quality forged steel body construction allows for higher lathe speeds
• Hardened and ground scroll is precision balanced, allowing longer life and greater accuracy
• Hardened jaws and pinions increase the life of the chuck
• American standard tongue & groove master jaws allow for greater flexibility in choice of top tooling

BT150-3-Jaw-Scroll-Chuck-2
master-balls_w_cover-3

Micro Test Ball Sets

Master test balls are made of tungsten carbide with a stainless-steel magnetic base and a threaded Delrin protective cover. Each set comes with a certification of calibration and traceability to at least 2.0 microinches (0.05 microns) accuracy after having been tested using ultra-precision form measurement gage, calibrated gage blocks directly traceable to NIST, and the Donaldson ball reversal technique to eliminate spindle error isolating only the error of the test ball itself.

Master Certification Artifact

ABTech’s large precision-ground diameter and face surfaces to easily locate gage heads and confirm system accuracy.

EAS-Master-Certification-Artifact-3-620x752
universal-Probe-Stand-with-fine-adj-base-3-489x1024

Universal Probe Stand with Fine Adjust Base Shown

Specifications:

• 24” travel vertical post with friction drive and lock
• 12” travel horizontal arm with friction drive, swivel, and lock
• Drive assembly with 360° swivel
• 1/4” Ø swivel mount for LVDT’s, electronic or dial indicators (indicators not included)

Base options:

• Portable base with 3-point hardened steel pads
• Portable base with built-in fine adjust feature
• Locking swivel mount for the side of granite surface plate*
*Requires threaded inserts in granite (not included)

Custom sizes are available on request.

Inspection Style Gage Stands

[Model GSI-24P/12A Shown]

Specifications:

• 24” vertical square post with rack-and-pinion drive
• Available with 12”, 14”, 18” horizontal arm with friction drive
• 1/4” Ø swivel mount for LVDT’s, electronic or dial indicators (indicators not included)
• Drive assembly with 360° swivel and locks to hold post and arm positions

Base options:

• Portable heavy-duty cast-iron base with 3-point hardened steel pads
• Locking swivel mount for the side of granite surface plate*
• T-slot base plate with locking swivel mount*
*Requires threaded inserts in granite or T-slot plate (not included)

Custom sizes are available on request.

Inspection-Style-Gage-Stand-3
GST-Toolroom-Style-Gage-Stand-1-579x1024

Tool Room Style Portable Gage Stands

[Model GST-24P/12A Shown]

Specifications:

• 1.0” diameter x 24” tall vertical post
• 5/8” diameter x 12” horizontal arm
• 360° manual swivel assembly with locks to hold post and arm positions
• 1/4” Ø swivel mount for LVDT’s, electronic or dial indicators (indicators not included)

Base options:

• Portable base with 3-point hardened steel pads
• Portable base with built-in fine adjust feature
• Locking swivel mount for the side of granite surface plate*
*Requires threaded inserts in granite (not included)

Custom sizes are available on request.

Ultra-Fine & Fine Adjust Probe Mounts

Can be used with most gage arms and with both the lever and plunger probe mounts
• Ultra-fine adjust has a .013" pitch adjustment screw
• Fine adjust has a .020" pitch adjustment screw

plunger-probe-with-mount_W-INSET
microform-fine-adjust-1

MicroForm Fine Adjust

This style fine adjust typically comes on any dual-probe MicroForm system as well as some of our gage stands
• Can only be used with the lever style probe
• MicroForm fine adjust has a .020” pitch adjustment screw

Adjustable Probe Mounts (Front and Back Shown)

These adjustable probe mounts are built to be used with the dovetail found on the lever probes.

Probe-mount_ft-bk_facing-1
TIR-Ft-Side-view-1-2

MicroTIR (Shown with Single and Dual Probe Adaptors)

This user interface displays the results in both traditional analog-style and digital formats. The maximum and minimum readings and TIR are captured, removing potential operator error and user subjectivity. You can input part numbers and descriptions, and your results can be saved or printed for customer verification or as a traveler for the part.

Lever-Type Probes (Shown without Mounting Clamp)

ABTech offers industry standard lever-type electronic indicators.

45-degree-probe-2-1024x721
cables-4

Extension Cables

These extension cables are made to be used with both the lever and plunger-style probes. There are various standard lengths available and custom lengths available on request.

Changeable Probe Tip Adaptor

This adapter will allow you to use 4-48 threaded probe tips allowing for an easy change of custom lengths, ball sizes, ball material etc. These adapters also eliminate left and right probe tip movement which reduces the chance of improper probe placement on part surfaces.

changeable_Probetip-adaptor-1
changeable_Probetips-3

Custom Probe Tips

ABTech has custom probe tips available for both lever and plunger-style probes – length, material, ball/tip size, shape

Gage Blocks for Probe Calibration

ABTech’s gage blocks are a system for producing precision lengths. These are used to calibrate our standard lever and plunger probes on our standard products that use electronic probes. The individual gage block is metal and is precision ground to a specific thickness. An important feature of gage blocks is that they can be joined together with very little dimensional uncertainty. A small number of gauge blocks can be used to create accurate lengths within a wide range.

 

Gauge-blocks-4
small-air-filter-regulator-1

Large Air Filter Regulator

To ensure lasting performance and contaminate protection for your air-bearing motion system ABTech offers two basic dual element filter/regulator accessory units. The small model unit (#00787AC) has a 5.0-micron pre-filter and 0.5-micron coalescing secondary filter and the larger model unit (#00938AD) has a 5.0-micron pre-filter and a 0.3-micron coalescing secondary filter.
If your air bearing motion system is powered then we recommend adding a safety interlock pressure sensor switch to detect the loss of air supply to the air bearing stage.

 

Electronics Carts

These electronics carts are used to mount monitors, PCs, and controllers, and provides shelf space for a keyboard, mouse, and an optional printer.

FRONT_bACK-MONITOR-3-1
FILTERS-4-1024x723

Replacement Air Filters

We have various replacement air filters on offer for both small and large air filters and regulators.

Anti-Rotational Lock

These anti-rotational locks are made for all EAS tables. They are classified as "best practice" for torquing parts, over shutting off the air supply.

IMG_6307-2-1
Replacement-Components-2

Replacement Components

Contact ABTech for any replacement or spare parts.

Need more information about Accessories?

Contact Us

Solutions

made in the USA

About

Join our mailing list and never miss an update.



126 Route 12 North
Fitzwilliam, New Hampshire 03447
(603) 585-7106
Contact Us

Proud Members of:
© 2024 Copyright ABTech Inc. All rights reserved. Privacy Policy Terms & Conditions